Silicone O-Ring Seals
Silicone O-Ring Seals for Static Sealing
A silicone O-ring creates a seal by compressing its circular cross-section in a suitable groove. Silicone is particularly suitable for static joints requiring temperature resistance, flexibility at low temperatures or food contact. For specification at Lindemann Silikon, we need details of the medium, temperature and installation space in addition to the inside diameter and cross-section diameter. These determine which silicone compound suits the sealing application.
The ordering dimensions usually consist of inside diameter × cross-section diameter. A specification such as 40 × 3 mm therefore describes a ring with an inside diameter of 40 mm and a cross-section diameter of 3 mm. Include dimensional tolerances and material requirements in the drawing so that purchasing and production work to the same specification.
Properties of Silicone
VMQ, a silicone rubber with methyl and vinyl groups, is frequently used for O-rings. Its strengths include heat resistance, elasticity at low temperatures and resistance to ozone and weathering. Its comparatively low tear and abrasion resistance limits its use on moving sealing surfaces. Material selection for rotating shafts or frequent reciprocating movements requires separate assessment. These properties are also described in the Parker O-Ring Handbook.
A temperature specification alone is not sufficient for approval. State whether the seal remains continuously warm, cools down regularly or experiences only brief temperature peaks. For cleaning processes, the cleaning agent, concentration and contact time must be included in the specification. Resistance to dry heat cannot be directly applied to hot water or steam.
Material Grades and Curing
Silicone grades differ in their compound, hardness and curing system, among other factors. Peroxide-curing and addition-curing systems, often referred to as platinum-curing systems, are commonly used. The curing method describes how the elastomer is manufactured. It does not replace evidence of suitability for food contact, nor does it alone determine mechanical behaviour.
Post-treatment is also part of material selection. Post-curing can reduce volatile constituents and influence the final properties. Whether and how post-curing is required depends on the particular compound and intended application. Guidance is provided in the WACKER silicone rubber processing brochure.
For an unambiguous order, we recommend a defined material designation including hardness and, where applicable, contact requirements. “Silicone, white” is not a sufficient specification. Colour can make identification easier during maintenance and assembly, but does not demonstrate composition or compliance.
Technical Data
The table lists the key specification points. Binding values must refer to the compound offered and the specific ring design.
| Property | Specification |
|---|---|
| Material | Silicone rubber, frequently VMQ |
| Geometry | Ring with a circular cross-section |
| Dimensions | Inside diameter × cross-section diameter in mm |
| Hardness | In Shore A, according to the agreed compound |
| Temperature range | Dependent on compound, medium and exposure time |
| Operating pressure | Dependent on installation space, sealing gap, hardness and temperature |
| Dimensional tolerances | According to the drawing or agreed specification |
| Food contact | Only with suitable supporting documentation for the specific version and use |
Applications by Industry
- Food and beverage equipment: Possible sealing locations include removable lids, fittings and housings. Describe the food product and the complete cleaning procedure, including downtime with residual media present.
- Equipment and machinery manufacturing: For static housing joints, the actual temperature at the groove and the assembly sequence are crucial. A temperature specification for the entire device often does not adequately describe the conditions experienced by the seal.
- Laboratory and analytical equipment: For closures and sample containers, include the chemicals used in the enquiry. For measurements sensitive to gases, requirements for permeation and permissible leakage must also be specified.
- Pharmaceutical equipment: For seals in contact with the product, the required material documentation and process conditions must be defined in advance. A food contact declaration does not replace application-specific qualification.
Selection Criteria for Engineering and Purchasing
To assess an enquiry, we need a drawing or a complete dimensional description. Also state whether sealing takes place axially between faces or radially between cylindrical components. An existing, previously used ring is only of limited use as a dimensional reference, because operation and installation may have altered its dimensions.
- Media: Specify product names, composition where known, and all cleaning agents or lubricants.
- Operating conditions: State operating pressure, pressure fluctuations, vacuum conditions, and minimum and maximum temperatures, including duration.
- Installation space: Provide groove dimensions, mating surfaces, gap dimensions and component tolerances.
- Procurement: Define quantity, recurring demand, desired marking and required documents.
When comparing quotations, the material, tolerances and scope of documentation should match. Also clarify whether the offered ring is moulded or joined from round cord. The joint must be considered in the technical assessment; identical nominal dimensions alone do not make the versions interchangeable.
Common Installation Errors
Sharp edges, exposed threads and unsuitable tools can damage the ring during insertion. Installation sleeves and suitable lead-in chamfers protect the sealing edge. Insert the ring evenly and avoid twisting. Lubricants must be compatible with both the silicone and the process medium. The relevant installation principles are explained in the Parker O-Ring Handbook.
If leaks recur, document the removed ring together with its installed position. Photos of the damage, groove and mating surface help distinguish installation errors from an unsuitable design. Changing to a different hardness without investigating the cause may allow the same failure to recur.
Compliance: BfR and FDA
For silicone in contact with food, BfR Recommendation XV “Silicones” provides a relevant basis for assessment. It contains requirements for starting materials and finished products. A BfR recommendation is not a product certification. For your order, the supporting documentation must cover the specific version and intended use.
The US regulation FDA 21 CFR 177.2600 concerns rubber articles intended for repeated food contact. Among other things, it governs permitted constituents and, depending on the type of contact, extraction requirements. “FDA-compliant” should therefore be documented with reference to the specific regulation and its scope of application. This does not constitute blanket approval for every process.
Related Products
Lindemann Silikon offers silicone tubing for conveying media. Guidance on specifying components in contact with products is available on our page about food-grade silicone.
FAQ on Silicone O-Ring Seals
Can I use the outside diameter when ordering?
Yes, provided the cross-section diameter is also specified and the dimensions are clearly labelled. The inside diameter is the outside diameter minus twice the cross-section diameter.
Does a harder O-ring always provide a better seal?
No. The hardness must suit the compression and the design. A change should be assessed based on the sealing application and should not be ordered solely because a leak exists.
What information do you need for a replacement seal?
If possible, send the original drawing, material designation and operating conditions. In the event of a failure, also provide the service duration and a description of when the leak occurs.
How can repeat orders be kept unambiguous?
Use a part number with a drawing revision and a defined material specification. Agree that changes to the compound, design or required supporting documentation must be agreed upon before delivery.






