{"id":19887,"date":"2026-11-18T09:00:00","date_gmt":"2026-11-18T08:00:00","guid":{"rendered":"https:\/\/lindemannsilikon.de\/2026\/11\/16\/edge-protection-profile-select-clamping-range-material-and-design\/"},"modified":"2026-11-19T20:14:40","modified_gmt":"2026-11-19T19:14:40","slug":"edge-protection-profile-select-clamping-range-material-and-design","status":"publish","type":"post","link":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/","title":{"rendered":"Edge protection profile: select clamping range, material and design"},"content":{"rendered":"\n<p class=\"wp-block-paragraph\">An edge protection profile is selected according to its clamping range (sheet thickness including coating), material (temperature and media) and design with or without a sealing head. The clamping range determines whether the profile stays securely in place over time. The material determines whether it remains elastic after years of service on an oven door, control cabinet or vehicle door. The design determines whether the profile simply covers the edge or also provides a seal. In application engineering, we see most complaints where one of these three factors was only roughly estimated. In most cases, this concerns the actual sheet thickness after coating.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Clamping range: sheet thickness after coating is what counts<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The clamping range specifies the material thickness for which the profile is designed. Common ranges include, for example, 1 to 2 mm, 1 to 3 mm, 2 to 4 mm or 3 to 6 mm. The relevant dimension is the edge thickness in the installed condition. A powder coating typically adds 60 to 120 \u00b5m per side. A 2 mm sheet can therefore easily measure 2,2 mm after coating on both sides. At overlapping joints, folds or welded tabs, the thickness may also vary along an edge.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">As our own design guideline, we recommend positioning the actual edge thickness within the middle third of the clamping range wherever possible. This leaves a margin for sheet and coating tolerances. Whether a profile also holds reliably near the limits of its clamping range depends on the profile design and should be approved by the manufacturer for the specific application. Where thickness varies along an edge, the clamping range must accommodate the thickest point. If the variation is too large, using two profile variants is the better solution.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Metal insert and gripping lips: secure retention without adhesive<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Profiles without an insert are held in place solely by the inherent elastic tension of the elastomer. They are suitable for thin edges, applications requiring only edge covering or use in combination with adhesive tape. For lasting retention on sheet metal edges, a stamped steel strip or aluminium insert is embedded in the profile. Slots in the strip allow the profile to bend around curves. The minimum bend radius depends on the profile height and the insert and should be specified in the drawing. Galvanised steel is standard. For outdoor and wet environments, a stainless steel insert is advisable because corrosion can develop at the cut edges of galvanised strips. This later appears as rust streaks at the profile ends.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Internal gripping lips provide frictional retention against the sheet surface. Multiple lips compensate for tolerances better than a single lip and increase the pull-off force. On smoothly painted or oiled sheets, frictional retention is sometimes insufficient. In such cases, a lip made from a softer compound or a bead of adhesive in the groove can help.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Material: silicone, EPDM or PVC according to temperature and environment<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Silicone<\/strong> typically covers -60 \u00b0C to +200 \u00b0C, depending on the compound, with special grades capable of withstanding higher temperatures for short periods. It resists ozone and UV and has a low compression set at elevated temperatures. We therefore use it on oven and heated cabinet doors, in food processing equipment and on enclosures exposed to large temperature fluctuations. For food contact, compounds are available that meet BfR Recommendation XV and FDA 21 CFR 177.2600 for rubber articles intended for repeated use. For railway applications, compounds with documented compliance with EN 45545-2 are available. Silicone&#8217;s limitations are its tear and abrasion resistance, which are typically lower than those of EPDM, and its limited resistance to mineral oils and fuels. Silicone designs and cross-sections can be found in our overview of <a href=\"https:\/\/lindemannsilikon.de\/en\/silicone-profiles\/\">silicone profiles manufactured to drawing<\/a>.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>EPDM<\/strong> resists weathering and ozone and is mechanically robust. Sulphur-cured EPDM is typically suitable for use up to approximately +120 \u00b0C, while peroxide-cured grades can be used up to approximately +150 \u00b0C. EPDM is not resistant to mineral oils and greases. It is the usual material for vehicle manufacturing and outdoor control cabinets, provided there is no oil exposure.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><strong>Flexible PVC<\/strong> is typically suitable for use between approximately -20 \u00b0C and +60 \u00b0C and is sufficient for indoor applications without thermal stress. Plasticisers can migrate over time. The profile then hardens and may soften paint finishes. In cold conditions, PVC becomes stiff and difficult to install. In a fire, it releases halogen-containing gases, which generally rules out PVC for railway applications and areas with requirements governing smoke gases.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Design with a sealing head: edge protection and sealing in one profile<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Profiles with a sealing head combine the clamping profile with a tubular or lip seal. If the head is on top, it seals against an opposing face, for example at a door rebate. If it is positioned on the side, it seals against a surface parallel to the sheet, such as on flaps and lids. The clamping section and head are co-extruded: the clamping section uses solid material for retention, while the head, depending on the design, is a cellular rubber tube for low closing forces or a solid elastomer lip. Silicone profiles with a tubular head frequently use <a href=\"https:\/\/lindemannsilikon.de\/en\/silikon-foam\/\">silicone foam<\/a>, which remains soft even at high temperatures. Silicone sealing lips, by contrast, are made from solid silicone.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The sealing head is designed according to the gap dimension and tolerance. For cellular rubber heads, compression is typically 25 to 40 % of the head height. Insufficient compression leaves gaps open, while excessive compression increases the closing force and causes permanent compression set in the head. The degree of protection achieved under EN 60529 depends on the entire enclosure, not on the profile alone. If a closed frame or a moulded gasket is a better solution than a continuous profile, the overview of <a href=\"https:\/\/lindemannsilikon.de\/en\/2026\/05\/01\/silikondichtungen-industrie-o-ring-flachdichtung-formdichtung-2\/\">silicone seals in industry<\/a> provides guidance.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Common installation and selection errors<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The most common error is using a cut sheet that has not been deburred. The burr cuts into the gripping lips, reduces retention force and can cause the insert to push through the profile at points subject to high loads. Just as frequently, the profile is driven into place with a steel hammer instead of being installed with a plastic mallet or pressure roller. This damages both the profile and the sheet coating.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A third issue is tension during installation. If the profile is stretched during fitting, it subsequently retracts and leaves a gap at the joint. It is better to install the profile without tension and with slight compression towards the joint. The joint should be positioned on an upper edge to prevent water from collecting there. At corners below the minimum bend radius, the profile wrinkles and the sealing head buckles. In these cases, a larger corner radius on the sheet, a notch cut in the profile or vulcanised frames with moulded corners are better choices.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Enquiry checklist for design engineers and purchasers<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">For a reliable quotation, we need the following information: <strong>Sheet thickness<\/strong> including coating and tolerance, along with the edge shape. <strong>Operating temperature<\/strong> for continuous operation and peak exposure. <strong>Media and environment<\/strong> such as oil, cleaning agents, UV, outdoor use or food contact. <strong>Design<\/strong> without a sealing head, with a head on top or on the side, plus the gap dimension and required compression. <strong>Compliance documentation<\/strong> such as BfR XV, FDA, EN 45545-2 or UL 94 with the required classification. <strong>Geometry<\/strong> including the smallest corner radius, supply format as coils, cut lengths or frames, and colour.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A sketch of the installation cross-section and details of the installation method, whether by hand, with a roller or automated, are helpful. If an existing profile is to be replaced, a sample and a description of the damage are often more informative than any data sheet.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\">Frequently asked questions<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\">Which clamping range is suitable for 2 mm sheet metal?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">The thickness after coating is decisive. A powder-coated 2 mm sheet typically measures approximately 2,1 to 2,3 mm. A clamping range of 1 to 3 mm is then suitable because this value falls approximately within its middle third. With a clamping range of 2 to 4 mm, it would be at the lower end. A narrower clamping range is advantageous where vibration occurs.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Does an edge protection profile always need a metal insert?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. Profiles without an insert are sufficient for thin edges, applications requiring only edge covering or bonded solutions. If the profile needs to stay securely in place over time without adhesive, particularly under vibration, with frequent opening or when fitted with a sealing head, a stamped steel, stainless steel or aluminium insert is standard.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">When is silicone preferable to EPDM?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Silicone is suitable when the temperature exceeds the typical range of EPDM, meaning continuous operation above approximately 120 to 150 \u00b0C, when food contact with documented compliance with BfR XV or FDA 21 CFR 177.2600 is required or when elasticity must be maintained in extreme cold. Under severe abrasion, EPDM is often more robust. Where oil exposure occurs, a material resistant to the specific medium is required.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\">Can an edge protection profile be bent around corners?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Yes, provided the profile&#8217;s minimum bend radius is maintained. This depends on the profile height, insert and sealing head. Smaller radii cause wrinkles and prevent the head from sealing. The alternatives are then a notch cut in the profile, a larger corner radius on the sheet or a vulcanised frame with a moulded corner.<\/p>\n\n\n\n<script type=\"application\/ld+json\">{\"@context\": \"https:\/\/schema.org\", \"@type\": \"FAQPage\", \"mainEntity\": [{\"@type\": \"Question\", \"name\": \"Which clamping range is suitable for 2 mm sheet metal?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"The thickness after coating is decisive. A powder-coated 2 mm sheet typically measures approximately 2,1 to 2,3 mm. A clamping range of 1 to 3 mm is then suitable because this value falls approximately within its middle third. With a clamping range of 2 to 4 mm, it would be at the lower end. A narrower clamping range is advantageous where vibration occurs.\"}}, {\"@type\": \"Question\", \"name\": \"Does an edge protection profile always need a metal insert?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"No. Profiles without an insert are sufficient for thin edges, applications requiring only edge covering or bonded solutions. If the profile needs to stay securely in place over time without adhesive, particularly under vibration, with frequent opening or when fitted with a sealing head, a stamped steel, stainless steel or aluminium insert is standard.\"}}, {\"@type\": \"Question\", \"name\": \"When is silicone preferable to EPDM?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Silicone is suitable when the temperature exceeds the typical range of EPDM, meaning continuous operation above approximately 120 to 150 \u00b0C, when food contact with documented compliance with BfR XV or FDA 21 CFR 177.2600 is required or when elasticity must be maintained in extreme cold. Under severe abrasion, EPDM is often more robust. Where oil exposure occurs, a material resistant to the specific medium is required.\"}}, {\"@type\": \"Question\", \"name\": \"Can an edge protection profile be bent around corners?\", \"acceptedAnswer\": {\"@type\": \"Answer\", \"text\": \"Yes, provided the profile's minimum bend radius is maintained. This depends on the profile height, insert and sealing head. Smaller radii cause wrinkles and prevent the head from sealing. The alternatives are then a notch cut in the profile, a larger corner radius on the sheet or a vulcanised frame with a moulded corner.\"}}]}<\/script>\n","protected":false},"excerpt":{"rendered":"<p>An edge protection profile is selected according to its clamping range (sheet thickness including coating), material (temperature and media) and design with or without a sealing head. The clamping range determines whether the profile stays securely in place over time. The material determines whether it remains elastic after years of service on an oven door,&hellip;<\/p>\n","protected":false},"author":8,"featured_media":19001,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_yoast_wpseo_canonical":"","_yoast_wpseo_opengraph-title":"","_yoast_wpseo_opengraph-description":"","_yoast_wpseo_opengraph-image":"","_yoast_wpseo_twitter-title":"","_yoast_wpseo_twitter-description":"","_yoast_wpseo_twitter-image":"","footnotes":""},"categories":[79],"tags":[],"class_list":["post-19887","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-silikonprodukte","category-79","description-off"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v26.4 (Yoast SEO v28.9) - https:\/\/yoast.com\/product\/yoast-seo-premium-wordpress\/ -->\n<title>How to choose the right edge protection profile | Lindemann<\/title>\n<meta name=\"description\" content=\"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Edge protection profile: select clamping range, material and design\" \/>\n<meta property=\"og:description\" content=\"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/\" \/>\n<meta property=\"og:site_name\" content=\"Lindemann Silikon\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-18T08:00:00+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-19T19:14:40+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png\" \/>\n\t<meta property=\"og:image:width\" content=\"1672\" \/>\n\t<meta property=\"og:image:height\" content=\"941\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/png\" \/>\n<meta name=\"author\" content=\"Jakub Koziel\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Written by\" \/>\n\t<meta name=\"twitter:data1\" content=\"Jakub Koziel\" \/>\n\t<meta name=\"twitter:label2\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data2\" content=\"8 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"Article\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#article\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/\"},\"author\":{\"name\":\"Jakub Koziel\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#\\\/schema\\\/person\\\/affdce01ff8eec7328c3c696a92bf30e\"},\"headline\":\"Edge protection profile: select clamping range, material and design\",\"datePublished\":\"2026-11-18T08:00:00+00:00\",\"dateModified\":\"2026-11-19T19:14:40+00:00\",\"mainEntityOfPage\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/\"},\"wordCount\":1538,\"publisher\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#organization\"},\"image\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/silikonschlauch-groessen-hero.png\",\"articleSection\":[\"Silikonprodukte\"],\"inLanguage\":\"en-US\"},{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/\",\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/\",\"name\":\"How to choose the right edge protection profile | Lindemann\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/silikonschlauch-groessen-hero.png\",\"datePublished\":\"2026-11-18T08:00:00+00:00\",\"dateModified\":\"2026-11-19T19:14:40+00:00\",\"description\":\"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#primaryimage\",\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/silikonschlauch-groessen-hero.png\",\"contentUrl\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2026\\\/05\\\/silikonschlauch-groessen-hero.png\",\"width\":1672,\"height\":941,\"caption\":\"Technische Silikonschl\u00e4uche in verschiedenen Gr\u00f6\u00dfen mit Innendurchmesser, Au\u00dfendurchmesser und Wandst\u00e4rke\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/2026\\\/11\\\/18\\\/edge-protection-profile-select-clamping-range-material-and-design\\\/#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Startseite\",\"item\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/home\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Edge protection profile: select clamping range, material and design\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#website\",\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/\",\"name\":\"Lindemann Silikon\",\"description\":\"Silikonhersteller aus Deutschland\",\"publisher\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/lindemannsilikon.de\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":[\"Organization\",\"LocalBusiness\",\"Manufacturer\"],\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#organization\",\"name\":\"Lindemann Silikon GmbH & Co. KG\",\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2020\\\/09\\\/cropped-logo_black-2.png\",\"contentUrl\":\"https:\\\/\\\/lindemannsilikon.de\\\/wp-content\\\/uploads\\\/2020\\\/09\\\/cropped-logo_black-2.png\",\"width\":512,\"height\":512,\"caption\":\"Lindemann Silikon\"},\"image\":{\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.linkedin.com\\\/company\\\/lindemannsilikon\"],\"legalName\":\"Lindemann Silikon GmbH & Co. KG\",\"email\":\"info@lindemannsilikon.de\",\"telephone\":\"+49-5351-544580\",\"vatID\":\"DE333444951\",\"address\":{\"@type\":\"PostalAddress\",\"streetAddress\":\"Dieselstr. 12\",\"postalCode\":\"38350\",\"addressLocality\":\"Helmstedt\",\"addressRegion\":\"Niedersachsen\",\"addressCountry\":\"DE\"},\"contactPoint\":[{\"@type\":\"ContactPoint\",\"telephone\":\"+49-5351-544580\",\"email\":\"info@lindemannsilikon.de\",\"contactType\":\"customer service\",\"areaServed\":[\"DE\",\"EU\",\"Worldwide\"],\"availableLanguage\":[\"de\",\"en\"]}],\"description\":\"Deutscher Hersteller von Silikonschl\u00e4uchen, Silikonprofilen und Silikonformteilen f\u00fcr Industrie, Lebensmittel-, Medizin- und Pharmatechnik.\",\"knowsAbout\":[\"Silikonschl\u00e4uche\",\"Silikonprofile\",\"Silikonformteile\",\"Silikonextrusion\",\"Silikon-Spritzguss\",\"Silikon-Coextrusion\",\"Lebensmittelechtes Silikon (BfR XV \\\/ FDA 21 CFR 177.2600)\",\"Hochtemperatur-Silikon (HT-VMQ)\",\"Fluorsilikon (FVMQ)\",\"Silikondichtungen\",\"Silikonsch\u00e4ume\",\"Silikon Pharma \\\/ Medizintechnik\"],\"slogan\":\"Silikonhersteller aus Deutschland\"},{\"@type\":\"Person\",\"@id\":\"https:\\\/\\\/lindemannsilikon.de\\\/#\\\/schema\\\/person\\\/affdce01ff8eec7328c3c696a92bf30e\",\"name\":\"Jakub Koziel\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g\",\"url\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g\",\"contentUrl\":\"https:\\\/\\\/secure.gravatar.com\\\/avatar\\\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g\",\"caption\":\"Jakub Koziel\"},\"url\":\"https:\\\/\\\/lindemannsilikon.de\\\/en\\\/author\\\/j-koziel\\\/\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"How to choose the right edge protection profile | Lindemann","description":"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/","og_locale":"en_US","og_type":"article","og_title":"Edge protection profile: select clamping range, material and design","og_description":"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.","og_url":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/","og_site_name":"Lindemann Silikon","article_published_time":"2026-11-18T08:00:00+00:00","article_modified_time":"2026-11-19T19:14:40+00:00","og_image":[{"width":1672,"height":941,"url":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png","type":"image\/png"}],"author":"Jakub Koziel","twitter_card":"summary_large_image","twitter_misc":{"Written by":"Jakub Koziel","Est. reading time":"8 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"Article","@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#article","isPartOf":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/"},"author":{"name":"Jakub Koziel","@id":"https:\/\/lindemannsilikon.de\/#\/schema\/person\/affdce01ff8eec7328c3c696a92bf30e"},"headline":"Edge protection profile: select clamping range, material and design","datePublished":"2026-11-18T08:00:00+00:00","dateModified":"2026-11-19T19:14:40+00:00","mainEntityOfPage":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/"},"wordCount":1538,"publisher":{"@id":"https:\/\/lindemannsilikon.de\/#organization"},"image":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#primaryimage"},"thumbnailUrl":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png","articleSection":["Silikonprodukte"],"inLanguage":"en-US"},{"@type":"WebPage","@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/","url":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/","name":"How to choose the right edge protection profile | Lindemann","isPartOf":{"@id":"https:\/\/lindemannsilikon.de\/#website"},"primaryImageOfPage":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#primaryimage"},"image":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#primaryimage"},"thumbnailUrl":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png","datePublished":"2026-11-18T08:00:00+00:00","dateModified":"2026-11-19T19:14:40+00:00","description":"Edge trim for sheet metal: select the grip range, metal insert, sealing bulb and silicone, EPDM or PVC material to suit the application.","breadcrumb":{"@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#primaryimage","url":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png","contentUrl":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2026\/05\/silikonschlauch-groessen-hero.png","width":1672,"height":941,"caption":"Technische Silikonschl\u00e4uche in verschiedenen Gr\u00f6\u00dfen mit Innendurchmesser, Au\u00dfendurchmesser und Wandst\u00e4rke"},{"@type":"BreadcrumbList","@id":"https:\/\/lindemannsilikon.de\/en\/2026\/11\/18\/edge-protection-profile-select-clamping-range-material-and-design\/#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Startseite","item":"https:\/\/lindemannsilikon.de\/en\/home\/"},{"@type":"ListItem","position":2,"name":"Edge protection profile: select clamping range, material and design"}]},{"@type":"WebSite","@id":"https:\/\/lindemannsilikon.de\/#website","url":"https:\/\/lindemannsilikon.de\/","name":"Lindemann Silikon","description":"Silikonhersteller aus Deutschland","publisher":{"@id":"https:\/\/lindemannsilikon.de\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/lindemannsilikon.de\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":["Organization","LocalBusiness","Manufacturer"],"@id":"https:\/\/lindemannsilikon.de\/#organization","name":"Lindemann Silikon GmbH & Co. KG","url":"https:\/\/lindemannsilikon.de\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/lindemannsilikon.de\/#\/schema\/logo\/image\/","url":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2020\/09\/cropped-logo_black-2.png","contentUrl":"https:\/\/lindemannsilikon.de\/wp-content\/uploads\/2020\/09\/cropped-logo_black-2.png","width":512,"height":512,"caption":"Lindemann Silikon"},"image":{"@id":"https:\/\/lindemannsilikon.de\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.linkedin.com\/company\/lindemannsilikon"],"legalName":"Lindemann Silikon GmbH & Co. KG","email":"info@lindemannsilikon.de","telephone":"+49-5351-544580","vatID":"DE333444951","address":{"@type":"PostalAddress","streetAddress":"Dieselstr. 12","postalCode":"38350","addressLocality":"Helmstedt","addressRegion":"Niedersachsen","addressCountry":"DE"},"contactPoint":[{"@type":"ContactPoint","telephone":"+49-5351-544580","email":"info@lindemannsilikon.de","contactType":"customer service","areaServed":["DE","EU","Worldwide"],"availableLanguage":["de","en"]}],"description":"Deutscher Hersteller von Silikonschl\u00e4uchen, Silikonprofilen und Silikonformteilen f\u00fcr Industrie, Lebensmittel-, Medizin- und Pharmatechnik.","knowsAbout":["Silikonschl\u00e4uche","Silikonprofile","Silikonformteile","Silikonextrusion","Silikon-Spritzguss","Silikon-Coextrusion","Lebensmittelechtes Silikon (BfR XV \/ FDA 21 CFR 177.2600)","Hochtemperatur-Silikon (HT-VMQ)","Fluorsilikon (FVMQ)","Silikondichtungen","Silikonsch\u00e4ume","Silikon Pharma \/ Medizintechnik"],"slogan":"Silikonhersteller aus Deutschland"},{"@type":"Person","@id":"https:\/\/lindemannsilikon.de\/#\/schema\/person\/affdce01ff8eec7328c3c696a92bf30e","name":"Jakub Koziel","image":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/secure.gravatar.com\/avatar\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g","url":"https:\/\/secure.gravatar.com\/avatar\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g","contentUrl":"https:\/\/secure.gravatar.com\/avatar\/2b43a84731345b999b96a0ddaf3b6ae9484a294ab3d76645ce7dfb0fe18dfce0?s=96&d=mm&r=g","caption":"Jakub Koziel"},"url":"https:\/\/lindemannsilikon.de\/en\/author\/j-koziel\/"}]}},"_links":{"self":[{"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/posts\/19887","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/users\/8"}],"replies":[{"embeddable":true,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/comments?post=19887"}],"version-history":[{"count":1,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/posts\/19887\/revisions"}],"predecessor-version":[{"id":19888,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/posts\/19887\/revisions\/19888"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/media\/19001"}],"wp:attachment":[{"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/media?parent=19887"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/categories?post=19887"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/lindemannsilikon.de\/en\/wp-json\/wp\/v2\/tags?post=19887"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}